PREPARER UNE REMOTE SESSION ET CONFIGURER SON CONTROLEUR / PREPARE A REMOTE SESSION AND SET YOUR CONTROLLER
FR
Configuration du contrôleur par l’utilisateur sur le LMX 64
Sur le LMX 64/64H, l’utilisateur a accès aux maps du moteur pour choisir ses propres paramètres dans la limite de la vitesse et de la puissance que LMX a fixée.
Le câble du contrôleur peut se connecter au niveau de la prise magnétique situé en dessous du compartiment de la batterie, ou pour les modèles plus anciens, la prise doit être accessible au niveau du trou d’évacuation sur le cadre. Celui-ci peut être protégé par quelques bouchons d’isolation.
Afin de réaliser un diagnostique du contrôleur, il faut installer le logiciel de Silixcon disponible dans le lien suivant : https://docs.silixcon.com/docs/sw/swtools/download
Autorisez le téléchargement du logiciel même si un message d’alerte affirme que le logiciel pourrait abimer votre ordinateur - Le logiciel est sécurisé.
Après avoir accepté les conditions d’utilisation, choisissez le dossier où télécharger le logiciel.
Puis, il vous sera demandé de choisir quels composants vous souhaitez télécharger. Choisissez les mêmes composants que sur la photo suivante.
Enfin, cliquez sur le bouton Installer et redémarrer votre ordinateur pour terminer l’installation.
Le logiciel Silixcon est maintenant disponible sur votre ordinateur et vous pouvez l’ouvrir en cliquant sur l’icone suivante.
Vous accédez alors à l’interface de lancement du logiciel.
Puis, cliquez sur l’icone emGUI. Le vélo n’a pas à être allumé, vous pouvez y accéder sans être connecté à la batterie.
Cliquez sur l’icone “loupe” de recherche. Le contrôleur apparait alors (SCLMX1).
Vous pouvez à présent appuyer sur le symbole “+” pour ouvrir la liste de paramètres.
Vous pourrez alors visualiser les différentes maps.
Sur chaque map, vous pouvez modifier la vitesse (0-45), la puissance (0-2500), pas couple (0-1), couple global (0-1), le niveau d’accélérateur (0-1).
Il existe des limites pour la vitesse et la puissance qui ne sont pas modifiables par l’utilisateur.
Si vous désirez modifier vous-même les paramètres, changez les, puis sauvegarder les en faisant un click droit sur le SCLMX en haut, puis sauvegarder en sélectionnant “main”.
Accès à distance pour les paramètres réservés pour le fabriquant
Certains paramètres ou diagnostiques nécessitent l’intervention du fabriquant.
Un rendez-vous à distance peut-être prit avec un responsable sur la plateforme de réservation suivante : https://httpsv2lmxbikescom.simplybook.it/v2/#book/count/1/
Avant le rendez-vous :
Soyez certain d’avoir la dernière version du logiciel Silixcon ( voir lien et instructions au dessus)
Soyez sûr d’avoir le câble USB et que le vélo soit détectable comme un USB périphérique.
Installez le logiciel open-source RUSTDESK : https://github.com/rustdesk/rustdesk/releases/tag/1.4.0 . Ce logiciel permet à l’intervenant d’avoir accès à l’ordinateur de l’utilisateur afin de vérifier et modifier d'éventuels paramètres.
EN
LMX 64 user controller setup
On the LMX 64/64H, the user has access to the power maps to set his own setup within the limits of speed and power LMX has set with master acces.
The cable can connect to the magnetic plug at the bottom of the battery compartment, or for the older type, the plug should be accessible in the drain hole of the frame. It may be protected by some black heat shrink.
In order to carry out the diagnostic, you have to install the following software from Silixcon :
https://docs.silixcon.com/docs/sw/swtools/download
Authorize the downloading of the software even if a message says that this software might harm your computer - it is secured.
After agreeing the terms of the software choose the file you want to download the software in.
Then, you will be asked to choose which components you want to download. Select the same components as on the following picture.
Finally, click on the Install button and reboot your computer to finish the download.
The Silixcon software is now available on your computer and you can open it by clicking on the following icon :
You are now on the LaunchPad of the Software.
Then, connect to emGUI. The bike does not need to be turned on, you can do it without battery.
Click the looking glass search icon. The controller will appear (SCLMX1)
You can then click on the “+” plus symbol to open the parameters list.
You will see the different maps.
On each map, you can set the speed (0-45), power (0-2500), pas torque (0-1), global torque (0-1), accelerator level (0-1).
There are global limits for speed and power that are not user settable.
If you want to change the parameters by your own, make the changes to each parameter, then save by right click on the SCLMX on the top, then save to main.
Remote access for manufacturer reserved settings
Certain settings or diagnostics data need manufacturer access credentials.
A meeting can be scheduled with our service works : https://httpsv2lmxbikescom.simplybook.it/v2/#book/count/1/
Before the meeting :
Make sure to have the latest silicon software installed (see link and instructions above)
Make sure you have the usb cable and the bike is detected as an usb peripheral
Install open-source RUSTDESK : https://github.com/rustdesk/rustdesk/releases/tag/1.4.0 This software will allow us to have access to your computer in order to check and modify the settings.